-
Indlæg
-
-
Hej alle,
Jeg har lige købt en maske, hvor der stod, at den var behandlet med et anti-fog materiale… jeg undrede mig over dette og var derfor i tvivl, om glasset skulle “behandles” med tandpasta eller ej… og fik derfor Kingfish til at skrive til fabrikanten.
Jeg synes, at det er et super svar og meget informativt – og derfor vil jeg gerne dele det med jer.
Her er mit svar fra Esclapez:
Fog is a problem encountered with every new mask purchased whatever the brand.
There is not more problems on ours than on another one.
But it is a fact that glasses with an electro vacuum treatment (yellow tinted) are more sensible to fog than standard glasses.Where does this fog come from?
Actually, even if the silicon is a really extraordinary material for use, it remains very dirty to work.
So that’s why we have to use very strong & very greasy products for unmolding the silicon. It’s called “unmolding agents”.
Unfortunately, after injection, the silicon soaks up a bit of these “unmolding agents”.
So when, the customer purchase a brand new mask, there is still some residues inside the silicon of the mask.
Once the mask is used by customer, these residues come out the silicon and create the fog on glasses.How to eliminate the “unmolding agents” remained in the silicon ?
The principle is to soak out the silicon from these residues.
These “unmolding agents” are really greasy but can be easily eliminated with good a detergent product.
So the main point is to make the detergent reach the residues stacked inside the silicon.The best ways for me after you purchased a brand new mask are:
1°) Unmount the glasses and the frame of your mask. Just keep the silicon skirt.
2°) Scrub the mask with dish soap. Submerge it in a bucket with boiled water + detergent (don’t be mean with this one !).
Leave it soaking out for 1day/1night. Redo the same operation once and then it is ok.3°)You could also put the silicon skirt into a dishwasher (high temperature)
4°) Sometimes you have very rebel masks ! In this case, there is a really radical way:
Scrub the mask with dish soap. Then use acetone for cleaning the glasses (a quick pass), just a bit on silicone. Be careful with this one for not damaging the silicon, don’t use a sponge ! But just a rag paper soaked with acetone. Scrub again with dish soap. Redo the same operation once and then it is ok.After such operations, trust me that you will never have problem of fog, ever
Anti-fog technology result to a special treatment (product) that we apply on the skirt.
It eliminates the “unmolding agents” and it greatly avoids the fog formation./Anders
-
-
Der findes vist flere løsninger på problemet.
Jeg fik at vide jeg skulle bruge tandpasta i masken, slibemidlerne ville fjerne silikonen men ikke ridse glasset – det har virket super, selvom første tur med brillerne havde en vis mint-duft omkring sig.
Her ses hvordan det gøres:
http://www.youtube.com/watch?v=uTB-ybg-xBYOg her på videoen gør han det med en lighter:
http://www.youtube.com/watch?v=AxkqJqM6UTABegge de to trick er hurtigere end at lade maskinen ligge i sæbevand et døgn…
-
Ingen af jer nævner at rengøre selve masken.. hvis det er der problemet kommer fra:
Once the mask is used by customer, these residues come out the silicon and create the fog on glasses.
Jeg tænker, at min fremgangsmåde bliver:
1. Vaske glasset grundigt med tandpasta
2. Vaske masken med noget opvaskemiddel.I øvrigt synes jeg, at det er interessant er at der er forskel duggen ift. typen af glas. Hvis jeg havde vidst det inden, så havde jeg nok købt en anden model.
it is a fact that glasses with an electro vacuum treatment (yellow tinted) are more sensible to fog than standard glasses.
-
Næh, det har du ret i. Bortset fra, at jeg skrev, at jeg kun havde hørt om det andet problem før;-)
Så nu hvor silikoneproblemet var så fint beskrevet så tænkte jeg, at jeg kunne byde ind med det andet velkendte problem.Jeg har fire masker; tre med glas-, en med plastiklinser. De første tre duggede alle efter tandpasta og sæbe men ikke efter brændemanøvren.
Jeg kendte ikke til at skulle skrubbe skørtet direkte, men det vil jeg da prøve med den næste.Shooter & Shooter - Fotograf & Spearo
-
-
Forum er sponseret af
- Du skal være logget ind for at svare på dette indlæg.
